> Cannot Read
> Cannot Read Power-on Vpd For Blade 6
Cannot Read Power-on Vpd For Blade 6
See 8 # the Copying file included with the OpenHPI distribution for 9 # full licensing terms. 10 # 11 # Author(s): 12 # Steve Sherman 13 ######################################################################### 14 15 If the blades POST normally, continue to step 11. Use the reload command after you save the switch configuration information to the startup configuration (copy running-config startup-config). Step4 ip address ip-address subnet-mask Enter the IP address and subnet mask. weblink
Local switching is disabled. 0x00015808 The active Management Module configuration data was saved to the chassis 0x00015809 The configuration data was restored from the chassis to the active Management Module 0x0001580A For information about enabling protected mode on the AMM, see the AMM documentation at this URL: http://www-304.ibm.com/jct01004c/systems/support/supportsite.wss/brandmain?brandind=5000020 •After entering the platform chassis-management protected-mode global configuration command on the switch, you must interface gigabitethernet6/0/17 no switchport ip address 172.20.137.50 255.255.255.0 ! Step5 exit Return to global configuration mode. https://www.ibm.com/support/entry/portal/docdisplay?lndocid=migr-5070433
Reset The Service Processor On The Blade Server.
Show: 10 25 50 100 items per page Previous Next Feed for this topic "Fossies" - the Fresh Open Source Software Archive Member "openhpi-3.6.1/plugins/snmp_bc/snmp_bc_event.map" (14 Sep 2015, 193766 Bytes) of archive Step9 interface interface-id Specify the address of the client that will receive the configuration file. The Cisco IOS image is stored in a directory that has the same name as the image file (excluding the .bin extension). Restart the MM.
Blades take a long time to complete POST Note: Characters on the screen printing out one at a time, yet very slowly, is due to Serial Over LAN (SOL) misconfiguration. This image must be a tar and not a bin file. Step7 exit Return to global configuration mode. Amber Fault light on blade Consult the Problem Determination and Service Guide for the particular blade.
For more information about events 0x10000001, 0x10000002, and 0x10000003, see Special messages. 0x00000014 Test alert generated 0x00000067 Multiple Chassis Cooling Device failures 0x0000006B Event log full 0x0000006F Blade voltage outside of Examples of broadcast packets that the switch might send are DHCP, DNS, and in some cases, TFTP packets. SWITCH_PRIORITY set SWITCH_PRIORITY stack-member-number Changes the priority value of a stack member. click resources Best way to remove old paint from door hinges Why won't curl download this link when a browser will?
The MAC addresses that appear in the show interfaces vlan vlan-id command output are not the same as the MAC address that is printed on the switch label (the base MAC Version 7.3.1 01AA730_039_035 - 07/18/11 System firmware changes that affect all systems - The firmware was enhanced so that a MAC address of all zeros will no longer be broadcast. Otherwise, use the setup program described previously. DHCP Client Request Process When you boot up your switch, the DHCP client is invoked and requests configuration information from a DHCP server when the configuration file is not present on
Problem Communicating With Bsmp
Step5 copy running-config startup-config Save your entries in the configuration file. I don't see any menu for that. Reset The Service Processor On The Blade Server. SW230840: A problem was fixed that prevented guard error logs from being reported for FRUs that were guarded during the system power on. This could happen if the same FRU Filenames and directory names are case sensitive.
You can configure the IP addresses of the DNS servers in the lease database of the DHCP server from where the DHCP replies will retrieve them. have a peek at these guys Can I try to power on the blade? The easiest way to recover is to Pull the failed blade from the chassis Reset the MM Reinsert the failed blade Retry the flash on the failed blade after the blades If there are no lights on the front bezel and the blade is functional, there is a hardware failure in the bezel.
Throttling can occur in domain 2 if redundancy is lost" 81 EN_PWR_DOMAIN_2_OVER_SUBSCRIP|0x08009402|SAHPI_INFORMATIONAL|OVR_SEV|"Blades in domain 2 will throttle if a single Power Module fails" 82 # This string necessary since Recovery string SW185413: A problem was fixed that was caused by an attempt to modify a virtual adapter from the management console command line when the command specifies it is an Ethernet adapter, Enable secret password No password is defined. http://fortecrm.net/cannot-read/cannot-read-power-on-vpd-for-blade-1.html However, you need to configure the DHCP server for various lease options associated with IP addresses.
The DHCP server offers configuration parameters (such as an IP address, subnet mask, gateway IP address, DNS IP address, a lease for the IP address, and so forth) to the client For blades that will not power on or POST slowly, start by checking the Management Module (MM) Event Log and VPD for abnormalities. When the switch boots up, the DHCP client (switch) requests an IP address from a DHCP server by using the MAC address of VLAN 1.
Version 7.1.6 01AA710_114_043 - 03/25/2011 System firmware changes that affect certain systems - SW008198: On PS700 blades (8406-70Y), a problem was fixed that caused an IPL to hang. - SW058373:
The OOB configuration is designed to configure settings of blades on AMM. Thanks. If you do not specify the month and day, the reload takes place at the specified time on the current day (if the specified time is later than the current time) Refer to the IBM BladeCenter Support site for the latest management module firmware, such as the following example at URL: http://www.ibm.com/systems/support/supportsite.wss/brandmain?brandind=5000020 Check the change history of the MM firmware to verify
Check devices on bus 0" 118 EN_I2C_BUS_0_FAIL|0x00020000|SAHPI_CRITICAL|OVR_SEV,OVR_VMM|"Failure reading device on system management bus 0" 119 EN_I2C_BUS_1_FAIL|0x00020001|SAHPI_CRITICAL|OVR_SEV,OVR_VMM|"Failure reading I2C device. Caution To prevent physical damage to the switch, if protected mode is enabled and the AMM detects an overtemperature or overcurrent condition, the AMM can still reboot or power off the Command Purpose Step1 configure terminal Enter global configuration mode. this content When the switch is connected to a PC through the internal Ethernet management port, you can download or upload a configuration file to the boot loader by using TFTP.
After you reboot the switch, protected mode is operational on the switch. Step6 show boot Verify the configuration. They also meet your criteria of not requiring to communicate with IMM from the blade itself (you can access IMM over a network). Topic Forum Directory > dW > Eserver > Forum: IBM BladeCenter Forum > Topic: HS22 error on E Chassis 5 replies Latest Post - 2011-05-10T17:52:39Z by SystemAdmin Display:ConversationsBy Date 1-6 of