> Cannot Ping
> Cannot Ping Default Gateway Solaris 10
Cannot Ping Default Gateway Solaris 10
Did a thief think he could conceal his identity from security cameras by putting lemon juice on his face? Which is why i turned fa0/2 into a routed port so that it would be just that a port that would route traffic. In my situation we hand off a dot1q tunnel from our A to TWC who then carries it viam MPLS to the Z site. Here is the scenario. Check This Out
Top Best Answer 0 Mark this reply as the best answer?(Choose carefully, this can't be changed) Yes | No Saving... tim wissman replied Jun 24, 2014 Are you at run level 3? You mentioned after the problem, the gateway is not reachable from server, did you snoop/tshark to see if packets are going out? Maybe set up a trunk but only allow the vlans you want to traverse the trunk.
Solaris 11 Can't Ping Gateway
I cannot assign a static route on this type of device. Tried: zpool status fmadm faulty svcadm restart samba No errors. Notices Welcome to LinuxQuestions.org, a friendly and active Linux Community.
just to make sure you do not have a typo of some kind - I am trying to think of what would cause this when adding a patch...I have had many Solaris Ping Command Quote networker050184 Went to the dark side.... And do you have a link light? why not try these out brownwrap View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by brownwrap 02-01-2011, 04:26 PM #2 repo LQ 5k Club Registered: May 2001
Quote Ryuksapple84 Senior Member Join Date Sep 2008 Location MD Posts 181 Certifications CCENT, CCNA R&S, Security, Wireless & Data Center, CCNP Data Center 03-29-201107:45 PM #11 The port on Developer does not see priority in git Development Workflow being followed How can I declare independence from the United States and start my own micro nation? As a started lab?? networking solaris failure share|improve this question edited Aug 5 '14 at 6:17 asked Jul 27 '14 at 1:10 Pete Baughman 1113 1 Those port 53 queries you see in netstat
Solaris Ping Command
problem.host.com# snoop -o tracefile Using device /dev/le (promiscuous mode) You can view the snoop file by using the -i switch and the filename in any of the standard modes, namely: Terse Just use the default vlan. Solaris 11 Can't Ping Gateway Jalal, I'm able to ping gateway from other systems that share same gateway. An SVI (Switch vlan interface), acts as a virtual layer 3 interface on the Layer3 switch.
I am using the internet router and the MLS connection as a point to point link. his comment is here try this: configure router on a stick so that MLS may act as the default gateway for the switch and any device behind it. What does an expansion in early december mean for the standard format? If i try to telnet to the MLS from the laptop connected to it i am unable to.
Cheers, Tom Remove advertisements Sponsored Links TomSu View Public Profile Find all posts by TomSu
#2 06-28-2011 DukeNuke2 Soulman Join Date: Jul 2006 As a matter of fact VLAN's are not utilized anywhere throughout the company. If you connect a switch to a router and want them to communicate, I am pretty sure you will have to trunk them. http://fortecrm.net/cannot-ping/cannot-ping-to-default-gateway.html
mridula Slackware 1 11-28-2005 05:27 AM Permanent Default Route DenD AIX 3 10-31-2005 01:52 PM All times are GMT -4.
All Rights ReservedAd Choices The information on Computing.Net is the opinions of its users. It's strange that the state is still listed as established. Whenever possible, try to duplicate the problem in a lab and troubleshoot it there.
Can anybody clue me in as to the next step here?
Presumably you are trying to ping it by dotted quad rather than name; in that case it shouldn't matter whether it is the default gateway or just another device on the The Cisco 2900XL is a Layer 2 device. share|improve this answer edited Jul 29 '14 at 8:13 answered Jul 27 '14 at 5:30 Olivier Dulac 2,695716 add a comment| up vote 1 down vote I have observed that running I am testing out a Layer 3 switch, Cisco 3550.
If that is successful, then your OS to hardware is good. I am able to get responses via other subnets but it is something from behind this Layer 3 switch that does not allow the ping responses to be sent back. How to react? navigate here Top Best Answer 0 Mark this reply as the best answer?(Choose carefully, this can't be changed) Yes | No Saving...
But I don't know what else to check ? The company I work for passes fiber connections across TWC on a regular basis and have no toruble using vlans. View the arp table to determine if the device that sent the ICMP echo response is the correct system, 76:06:0b. # arp -a Net to Media Table: IPv4 Device IP Address If you do not need multiple vlans, you do not need a trunk link. 3.
If I perform sys-unconfig do I loose hostname too or only network setting? Can any one come up with solution Top Best Answer 0 Mark this reply as the best answer?(Choose carefully, this can't be changed) Yes | No Saving... All rights reserved. brownwrap View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by brownwrap 02-02-2011, 02:04 PM #11 Blinker_Fluid Member Registered: Jul 2003 Location: Clinging
Not directly related to your issue but I noticed that you're using TWC fiber connections. Heh. Operator ASCII art Did a thief think he could conceal his identity from security cameras by putting lemon juice on his face? If it showed other hosts on your network can you ssh from them into the box that is having issues?
Focus on one area at a time.